糖果派对官方网站

Full automatic blow moulding machine

hot key words

contact us

1493252937934201.jpg

Suzhou Kautas Machinery Co., Ltd

Address:Zhongxing intersection of Gangcheng Avenue, Zhangjiagang City, Jiangsu Province 

Contact:Mr Mike Xu      

Tel : 0086-13906242281     

E-mail:

China.kautas@gmail.com




Practice of automatic bottle blowing machine

Your current location: Home >> News >> Solutions

Practice of automatic bottle blowing machine

Release date:2017-06-26 00:00 source: Click:

       

Through the practice of Automatic blow molding machine over the years, we also feel that imported bottle blowing machines, especially large bottle blowing machines, are not perfect, and there are also many problems and defects. Through our study and deepening of the bottle blowing machine, we find out the problems, and boldly improve some problems, and have achieved better results.

Although the blow molding machine fault complex, the myriads of changes, as long as we take seriously, to cultivate high-quality electromechanical maintenance team, through reading and asked to think, practice, accumulate experience, master maintenance skills, mastery, we must be able to rely on its own strength, to make good use of the bottle, tube well. Bottle blowing machine troubleshooting should practice more, that is, more practice:

1., practice more and learn to do it

The automatic bottle blowing machine maintenance personnel, to be bold but cautious, dare to do, can only speak, do not, repair bad bottle blowing machine. But to mature, then do not blindly, otherwise it will expand the failure, resulting in accidents, the consequences will be unimaginable. At the same time, we must also be good at hands-on, first of all, the machine should be familiar with the operation of the bottle blowing panel and the contents of the menu, operate freely. At the same time, it is necessary to make full use of the self diagnosis technology of bottle blowing machine to deal with the faults quickly. Now the development of bottle blowing machine, and is more powerful.

2., we should practice more and develop practical skills and practical skills

Sometimes the bottle blowing machine looks fuzzy fault, it is not clear whether the fault of electrical or mechanical failure, we use a separate method to completely separate, there are many other methods to control the electrical part and the original circuit, such as "isolation" and "replacement method" and "comparative method", "tapping" etc. the method can be used as an effective means to help us find and eliminate the fault.

3., practice more and learn how to use the relevant instruments

For example, oscilloscope, multimeter, online detection circuit, short circuit tester, computer programmer, etc. can help us to judge and check the specific circuit, especially PLC, computer programmer, skilled use, free input and output parameters of blow molding machine, online test, system initialization etc.. This is helpful for analyzing faults, especially complex faults and solving problems.

4., we should practice more and carry out reforms"

Often occurs during the normal operation of a damaged element (such as switches, buttons, relays etc.) and no spare parts, repair yourself as much as possible or with special temporary bonding with other methods, the bottle blowing machine can work normally, wait until after the recovery of spare parts.

5., practice more, and do it yourself, Shui Ko

Generally speaking, blowing bottle circuit board reliability is good, the failure rate is very low, generally go to check the bottle blowing machine, do not doubt the board first. It can be eliminated by trial and error, initialization, hot and cold start, PLC and other methods. If it does prove a circuit board problem, fix it. These boards (usually no drawings) are expensive, so the quality of the circuit boards of the bottle blowing machine is very important. Once the circuit board is damaged, there is no spare parts, and the repair is not good at once. It will stop and seriously affect the production. Sometimes just a small circuit board fault, as long as the serious examination, it is not difficult to find problems, we have repeatedly found that individual capacitor leakage, board weld, short circuit fault, some circuit board fault is more complex, but as long as the time, through the inspection instruments, also is to fix the circuit board; but there are some situations seriously, especially the large scale integrated circuit, difficult maintenance, plus the original devices, spare parts, can only buy or send out early prepared plate repair. DIY repair board, is of great benefit, one can save costs for enterprises, on the other hand can solve as pressing danger, "dissecting a sparrow" familiar with electronic circuit analysis, training their own judgment and ability is very useful。


小机.jpg

Related tags:Automaticblowmoldingmachine

Recently Viewed:

S
e
r
v
i
c
e
  • service
二维码

Scan QR code

share it
糖果派对官方网站|糖果派对娱乐网站|官方网址版权所有